 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TIC216 SERIES SILICON TRIACS Sensitive Gate Triacs 6 A RMS Glass Passivated Wafer 400 V to 800 V Off-State Voltage Max IGT of 5 mA (Quadrants 1 - 3) MT1 MT2 G TO-220 PACKAGE (TOP VIEW) 1 2 3 Pin 2 is in electrical contact with the mounting base. MDC2ACA absolute maximum ratings over operating case temperature (unless otherwise noted) RATING TIC216D Repetitive peak off-state voltage (see Note 1) TIC216M TIC216S TIC216N Full-cycle RMS on-state current at (or below) 70C case temperature (see Note 2) Peak on-state surge current full-sine-waveat (or below) 25C case temperature (see Note 3) Peak gate current Peak gate power dissipation at (or below) 85C case temperature (pulse width 200 s) Average gate power dissipation at (or below) 85C case temperature (see Note 4) Operating case temperature range Storage temperature range Lead temperature 1.6 mm from case for 10 seconds IT(RMS) ITSM IGM PGM PG(AV) TC Tstg TL VDRM SYMBOL VALUE 400 600 700 800 6 60 1 2.2 0.9 -40 to +110 -40 to +125 230 A A A W W C C C V UNIT NOTES: 1. These values apply bidirectionally for any value of resistance between the gate and Main Terminal 1. 2. This value applies for 50-Hz full-sine-wave operation with resistive load. Above 70C derate linearly to 110C case temperature at the rate of 150 mA/C. 3. This value applies for one 50-Hz full-sine-wave when the device is operating at (or below) the rated value of on-state current. Surge may be repeated after the device has returned to original thermal equilibrium. During the surge, gate control may be lost. 4. This value applies for a maximum averaging time of 20 ms. electrical characteristics at 25C case temperature (unless otherwise noted ) PARAMETER IDRM Repetitive peak off-state current Gate trigger current VD = rated VDRM Vsupply = +12 V IGT Vsupply = +12 V Vsupply = -12 V Vsupply = -12 V TEST CONDITIONS IG = 0 RL = 10 RL = 10 RL = 10 RL = 10 TC = 110C tp(g) > 20 s tp(g) > 20 s tp(g) > 20 s tp(g) > 20 s MIN TYP MAX 2 5 -5 -5 10 mA UNIT mA All voltages are with respect to Main Terminal 1. DECEMBER 1971 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 1 TIC216 SERIES SILICON TRIACS electrical characteristics at 25C case temperature (unless otherwise noted) (continued) PARAMETER Vsupply = +12 V VGT Gate trigger voltage On-state voltage Holding current Latching current Critical rate of rise of off-state voltage Critical rise of commutation voltage Vsupply = +12 V Vsupply = -12 V Vsupply = -12 V VT IH IL dv/dt dv/dt(c) IT = 8.4 A Vsupply = +12 V Vsupply = -12 V Vsupply = +12 V Vsupply = -12 V VDRM = Rated VDRM VDRM = Rated VDRM TEST CONDITIONS RL = 10 RL = 10 RL = 10 RL = 10 IG = 50 mA IG = 0 IG = 0 (see Note 6) IG = 0 ITRM = 8.4 A TC = 110C TC = 70C 2 tp(g) > 20 s tp(g) > 20 s tp(g) > 20 s tp(g) > 20 s (see Note 5) Init' ITM = 100 mA Init' ITM = -100 mA 4 -2 20 5 MIN TYP MAX 2.2 -2.2 -2.2 3 1.7 30 -30 V mA mA V/s V/s V UNIT All voltages are with respect to Main Terminal 1. NOTES: 5. This parameter must be measured using pulse techniques, t p = 1 ms, duty cycle 2 %. Voltage-sensing contacts separate from the current carrying contacts are located within 3.2 mm from the device body. 6. The triacs are triggered by a 15-V (open-circuit amplitude) pulse supplied by a generator with the following characteristics: R G = 100 , tp(g) = 20 s, tr = 15 ns, f = 1 kHz. thermal characteristics PARAMETER RJC RJA Junction to case thermal resistance Junction to free air thermal resistance MIN TYP MAX 2.5 62.5 UNIT C/W C/W 2 DECEMBER 1971 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP TIC216 SERIES SILICON TRIACS MECHANICAL DATA TO-220 3-pin plastic flange-mount package This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. TO-220 4,70 4,20 o 3,96 3,71 10,4 10,0 2,95 2,54 6,6 6,0 15,32 14,55 1,32 1,23 18,0 TYP. 6,1 5,6 0,97 0,66 1 2 3 1,47 1,07 14,1 12,7 2,74 2,34 5,28 4,68 2,90 2,40 0,64 0,41 ALL LINEAR DIMENSIONS IN MILLIMETERS NOTE A: The centre pin is in electrical contact with the mounting tab. DECEMBER 1971 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 3 |
Price & Availability of TIC216
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |